top of page

Raspberry Pi 5 Camera Cable 22 Pin to 15-Pin: Buy and Use

1 hour ago
5 min read

To connect an older 15-pin camera to a Pi 5, you need a Raspberry Pi 5 camera cable 22 pin to 15-pin adapter. The narrow 22-pin, 0.5 mm end goes into the Pi 5. The wider 15-pin, 1 mm end goes into the camera. Power the Pi off, seat both ends with the exposed contacts facing the contacts inside each connector, lock the latches, and confirm detection with rpicam-hello --list-cameras.


The trouble is that the Pi 5 changed its camera connector. Your old Camera Module V1, V2 or HQ camera won't fit with the cable it came with. Cable listings look nearly identical, and a cable meant for a display or for the reverse direction fails silently. The ribbon also looks the same on both faces, so it is easy to insert it upside down. The result is the dreaded "no cameras available" message and an hour of guessing.


This guide covers what to buy and why, then walks through the four steps to connect the cable and test it. It ends with a troubleshooting table. Vadzo builds MIPI CSI-2 camera modules with Raspberry Pi 5 driver support, so connector details like these matter to us.


Why the Raspberry Pi 5 Camera needs a 22-pin to 15-pin cable


The Pi 5 uses a smaller 22-way, 0.5 mm pitch camera connector. Raspberry Pi's V1, V2 and HQ cameras still use the older 15-way, 1 mm pitch connector. A 22-pin to 15-pin cable bridges the two.


Two connectors, one adapter


The Pi 5 has two four-lane MIPI connectors, and each one can take either a camera or a display. They use the same "mini" 22-way format as the Compute Module development kit. Earlier A and B series boards used the 15-way "standard" format, and so do the cameras sold with them. The Pi Zero series, like the Pi 5, uses the 22-pin size.


You can't force the two together, and you shouldn't try. The adapter is a flat flexible cable (FPC) with a different connector size on each end.


The 22-pin end always goes to the Pi 5, and the 15-pin end always goes to the camera.

How to choose the right cable


Check these four points before you buy:



  • The listing says Pi 5, 22-pin 0.5 mm to 15-pin 1 mm.

  • It is sold as a camera cable. Display cables share the connector format, but a camera cable should not be used with a display, and the reverse is also true.

  • It is not a reverse adapter. Cables built to put a 22-pin camera on a 15-pin Pi, such as a Pi 4, are routed differently and don't work the other way round.

  • The length fits your build.


Measure the route the cable will take with a piece of string, then add 30 to 50 mm of slack. Expect to pay a few dollars per cable.


Length

Best for

200 mm

Camera mounted right beside the Pi, in a tight case

300 mm

Camera a few inches from the board, small enclosures

500 mm

Camera on an arm, a front panel or a separate part of the housing


When an adapter is the wrong answer


Some old cameras, such as the Pi Spy camera, have the ribbon permanently attached and no connector at the module end. An adapter has nothing to plug into. A 15-pin to 15-pin joiner is the better route than soldering.


If you are designing a product instead of reviving a spare module, start from a camera built for the Pi 5. Vadzo's Bolt-1335CRS, for example, is a 13MP color MIPI CSI-2 board from $165. Check each product page for its connector. Vadzo can also customize cable length and connector type for OEM orders.


Step 1. Power down and open both latches


Shut the Pi down completely and unplug the power before you touch either connector. Plugging a flat cable in while the board is live risks shorting pins, and that can damage the sensor or the Pi.


Shut down cleanly


Run the command below, wait for the activity LED to stop blinking, then pull the power. Disconnecting power without a shutdown can corrupt the SD card.


sudo shutdown -h now


Open the latches


Each connector has a small plastic latch. Lift it gently with a fingernail, not a screwdriver. The latches are fragile, and a snapped latch means a dead port. Open the latch on the Pi 5 and on the camera board, and don't force either one.


Either Pi 5 port accepts a camera. Note which one you use, because you may need that number in software later.


A latch that moves with light pressure is open, and a latch you have to force is the wrong one.

Step 2. Seat the 22-pin end in the Pi 5


Insert the narrow 22-pin end with its exposed contacts facing the contacts inside the connector. Push it straight in until it stops, then close the latch.


Check the contact side


Look into the open connector and find the row of metal contacts. The bare contacts on your cable must face them. On the Pi 5, gold contacts facing up is the wrong way. They face toward the Ethernet and PoE header side of the board. If your cable's markings suggest otherwise, trust what you see inside the connector.



Push in and lock


Hold the cable square to the connector so one corner doesn't go in first. Slide it in until the end bottoms out, then press the latch down flat. Give the cable a very light tug. It should stay put.


Step 3. Connect the camera and test


Connect the 15-pin end the same way, then boot the Pi and ask the software what it sees. If a camera shows up in the list, the cable is working.


Attach the 15-pin end


The V1, V2 and HQ boards use a 15-pin connector with lower contacts, so the exposed contacts on the cable face the camera board. Open the latch, slide the cable in square, and lock it. Route the cable with a gentle curve. A sharp crease can crack the copper traces inside, and the failure may only appear intermittently.



Boot and test


Power on and run these commands. On older Raspberry Pi OS releases, the same tools are named libcamera-hello and libcamera-still.


rpicam-hello --list-cameras rpicam-hello -t 5000 rpicam-still -o test.jpg


The first command should list a sensor such as ov5647 (V1), imx219 (V2) or imx477 (HQ). The second shows a five-second preview. Add -n if you are running headless. If you have two cameras, select one with --camera 0 or --camera 1.


Step 4. Troubleshoot a camera that isn't detected


Nearly every failure comes down to orientation, seating, or the wrong cable type. Work through the table from top to bottom.


Quick fault table


Symptom

Likely cause

Fix

"No cameras available"

Cable flipped or not fully seated

Power off, reopen both latches, flip, reseat

Camera works on one port only

Wrong port or camera index

Use --camera 1 or move the cable

New cable never works

Display cable or reverse-direction adapter

Check the listing against Step 2

Dropouts or noise

Creased cable or unlocked latch

Reseat, then replace with a fresh cable


Isolate the cable from the camera


Swap the cheap part first. A spare cable costs a few dollars, while a replacement camera costs far more. If a second cable gives the same result, test the camera on an older Pi with its original 15-pin cable.


If the camera works there, the fault is in the adapter or the Pi 5 connection. If it doesn't, the camera is the problem.


Change one thing at a time and change the cheapest part first.

Plug it in right the first time


The 22-pin end goes to the Pi 5, and the 15-pin end goes to the camera. Use a camera cable rather than a display cable, and pick a length that leaves slack without a tight bend. Check the contact side, lock both latches, then confirm with rpicam-hello --list-cameras.


If you are moving past old modules and building a product around the Pi 5, see Vadzo's MIPI CSI-2 cameras. Our application engineers can help with camera selection, cable length and connector requirements.

 
 

Reach Vadzo Team for the Customization

Vadzo team shall be able to assist you with the details on this.

contact form camera image
bottom of page