top of page

Stacked Sensor vs Global Shutter: What Actually Differs

6 days ago
6 min read

A stacked sensor vs global shutter comparison sets two different ideas against each other. A stacked sensor is a chip built in layers, with the pixels on top and fast processing circuitry, often memory, underneath, so the sensor reads out its data quickly. A global shutter is an exposure method in which every pixel starts and stops capturing at the same instant. Stacked designs shrink rolling shutter distortion, while global shutters remove it. For most photographers a stacked sensor is the better buy. If you shoot fast motion under flash or build machine vision systems, global shutter is the safer choice.


This article explains why the difference matters, how to choose between the two, and what each one costs you in dynamic range and money. It also shows how real cameras combine them and where global shutter dominates outside photography.


Vadzo designs global shutter camera modules for robots, AGVs and traffic systems, so we deal with this trade-off on real projects. The physics is the same whether you are buying a mirrorless body or a module.


Why the stacked sensor vs global shutter choice matters


Both technologies attack rolling shutter distortion, but they leave different leftovers. A stacked sensor leaves a small residual skew and costs less. A global shutter leaves none, but you pay in price and, usually, image quality.


What rolling shutter does to an image


Most CMOS sensors expose and read out one row at a time, so the top of the frame is captured slightly before the bottom. On a 2048-row sensor with a 10 µs line time, that gap is about 2 ms. Older or slower sensors can take tens of milliseconds.


The visible results are skewed vertical lines when you pan, a "jello" wobble in video, a flash that lights only part of the frame, and dark bands under flickering LEDs.


How each technology attacks the problem


A stacked sensor moves the processing and memory into a layer beneath the pixels, so signals travel a shorter path and the scan finishes sooner. A global shutter stores each pixel's charge in place, then reads the frame afterward, so there is no scan gap at all.



Here is a worked example. A car moving at 100 km/h covers about 27.8 meters per second. This table shows how far it travels between the first and last row being read:


Readout time

Car movement during readout

Result

30 ms (older sensor)

about 83 cm

Obvious lean

4 ms (fast stacked)

about 11 cm

Slight skew

2 ms (very fast stacked)

about 5.6 cm

Barely visible

Global shutter

0 cm

No skew


A stacked sensor shrinks the time gap between rows, while a global shutter removes it.

How to choose between a stacked sensor and a global shutter


Start with your subject and your lighting, then check three numbers on the spec sheet. Most people will be well served by a fast stacked sensor, and only a specific set of jobs truly needs a global shutter.


Match the technology to what you shoot


What you shoot

Better fit

Why

Sports and wildlife in daylight

Fully stacked sensor

Fast bursts, strong autofocus, better dynamic range

Fast subjects lit by flash

Global shutter

Flash can sync at very high shutter speeds

Video with fast pans or drone footage

Global shutter or very fast stacked

No jello, no skew

Scenes under LED or flickering light

Global shutter

No banding across the frame

Landscapes, portraits, travel

Either, or neither

Rolling shutter rarely shows, so save the money

Robotics and machine vision

Global shutter

Moving targets, strobed light, exact timing


Check three numbers on the spec sheet


Manufacturers do not always publish the figures that matter, so look for these in reviews and datasheets:


  • Readout time. Under about 5 ms is good for most action. Lower is better.

  • Flash sync speed. A rolling shutter body typically syncs around 1/200 s. A global shutter can sync at any shutter speed.

  • Dynamic range and base ISO. Compare measured results, because global shutter sensors have historically given up some range.


A fast stacked sensor can beat an early global shutter sensor in most practical scenarios, because its image quality is better and its residual skew is small. Do not pay for a global shutter unless your work shows skew or banding today.


Choose a global shutter for flash, flicker, and precise timing, and a fast stacked sensor for everything else.

Stacked sensor vs global shutter: pros, cons, and cost


A stacked sensor gives you speed at a premium price, and a global shutter gives you zero distortion at a higher premium. Here is how they compare on the points buyers ask about most.


Side-by-side comparison


Factor

Stacked sensor

Global shutter

What it is

Layered chip design

Exposure and readout method

Rolling shutter

Reduced, not eliminated

Eliminated

Readout speed

Very fast

Fast, with a storage step

Flash sync

Limited by shutter type

Any shutter speed

Dynamic range

Typically better

Usually lower, though the gap is narrowing

Low-light noise

Generally cleaner

Often a little worse

Cost

High, falling

Highest


The main downsides of a global shutter are cost, a dynamic range penalty, and sometimes more noise. Each pixel needs extra storage circuitry, which takes space that would otherwise collect light.


What drives the cost


Stacking requires bonding wafers, which is why it began in flagship bodies. It is now moving down. Nikon's partially stacked Z6III launched at about $2,500. Global shutter has stayed more expensive. Sony's a9 III, the first full-frame mirrorless camera with a global shutter, launched at about $6,000.


You pay for the technology rather than the image quality. A cheaper stacked body often gives you cleaner files than a costlier global shutter body.


A stacked sensor is the better general-purpose speed upgrade, and a global shutter is a specialist tool.

Fully stacked, partially stacked, and combined designs


You can have both technologies in one sensor, and buyers should know that stacked comes in degrees. Marketing often hides which version a camera has.


Fully stacked vs partially stacked


A fully stacked sensor typically adds both a logic layer and a memory buffer under the pixels, which gives the fastest readout and the highest sustained burst rates. A partially stacked sensor adds circuitry but usually not the full memory layer. It reads out faster than an unstacked sensor but slower than a fully stacked one. For daylight action and casual bird photography, the partial version is often enough. For the fastest subjects, it shows more skew.



Can one sensor be both?


Yes. Stacked describes how the chip is built, and global shutter describes how pixels expose. The Sony a9 III pairs a stacked sensor with a global shutter, shooting 120 frames per second at full resolution, with flash sync up to 1/80,000 s using compatible flashes. Sony's Pregius S industrial sensors also combine a back-illuminated stacked design with a global shutter.


Stacked and global shutter are not rivals on the same axis. The best sensors combine them.

Global shutter in embedded and machine vision


In embedded and machine vision, global shutter is the default, because the cameras watch moving things under controlled, often strobed, light. Rolling shutter skew in a robot's navigation image or a barcode on a conveyor causes errors, not just ugly photos.


Why modules favor global shutter


A robot moving at a few meters per second, a parcel on a belt, or a vehicle passing a toll point can each distort badly under a slow row scan. Global shutter also lets a strobe light the whole frame at once. Image-quality penalties matter less here, because lighting is controlled and the algorithm needs geometry, not tonal beauty.


Examples from Vadzo's range




Vadzo also offers a rolling shutter camera, the 20MP Falcon-2020MRS, for scenes that hold still and need resolution.


If your subject or your camera moves, a global shutter protects your data, and if neither moves, rolling shutter is fine.

Which one to pick


A stacked sensor is the right upgrade when you want speed, better autofocus, and little distortion without sacrificing image quality. A global shutter is the right pick when any skew, banding, or flash limit costs you the shot or the measurement. The best cameras now offer both in one sensor.


If you are building a product, not choosing a camera body, the decision is simpler: moving scenes call for a global shutter. You can browse Vadzo's global shutter camera modules and talk to the application engineering team about the right sensor for your project.

 
 

Reach Vadzo Team for the Customization

Vadzo team shall be able to assist you with the details on this.

contact form camera image
bottom of page